How to Arm Your Security System
AWAY is used when the user is away from the premise and wants the interior protected. Listed below are the steps to arm in the AWAY Mode:
Step 1 Close all protected doors and windows.
- Ready light will be on or flashing when all protected zones and sensors are secure. NOTE: If any zones are bypassed, a sensor in that zone can be violated without affecting the ready light.
- The security system will not arm if the ready light is not on or flashing.
- Enter your 4 or 6 digit user code to arm the system.
- The armed and exit lights will illuminate.
- You may now leave the building.
STAY is used when the user is inside the
premise and wants protection around the perimeter.
Step 1 Close all protected doors and windows.
- Ready light must be on or flashing when all protected zones and sensors are secure. NOTE: If any zones are bypassed, a sensor in that zone can be violated without affecting the ready light.
- The security system will not arm if the ready light is not on or flashing.
- Enter your 4 or 6 digit user code.
- Step 3 Press the [STAY] key.
- The stay light will illuminate indicating that all interior zones are bypassed.
How to Bypass a Zone
BYPASSING ZONES
If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. The following steps are used for bypassing zones:
Step 1 Press the [BYPASS] key.
Step 2 Enter user code, if required (optional). The bypass light flashes.
Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass. (Example: Press the [1] key for zone 1, press [1] – [2] for zone 12.)
Step 4 Press the [BYPASS] key again.
Step 5 The corresponding zone light will illuminate indicating the zone has been bypassed. Repeat steps 3 and 4 for any other zone(s) that need to be bypassed.
Step 6 Press the [BYPASS] key again -or- press the [#] key to exit the Bypass Mode. The bypass light will stop flashing upon exiting the Bypass Mode.
How to Add a Security Code
CHANGING USER CODES
Step 1 Your system must be in the Disarmed state to change user codes.
Step 2 Press [r]-[5].
Step 3 Enter a “Master Arm/Disarm Code”.
NOTE: For partitioned systems, someone changing the code of another person must have access to all or more partitions than the user being changed.
Step 4 The ready light will flash.
Step 5 Enter the 2 digit “user number” (always enter 2 digit such as [0] – [3] for user 3, or [5] – [2] for user 52).
Step 6 Enter the new four (4) or six (6) digit “user code”.
Step 7 The ready light will flash indicating you are back at Step 4 above. If the code is rejected, the sounder will beep 3 times.
Step 8 If another “user code” needs to be programmed, return to Step 5.
Step 9 Press the [#] key while the ready light is flashing to exit the User Code Programming Mode.
How to Delete a Security Code
DELETING USER CODES
Step 1 Your system must be in the Disarmed state to delete user codes.
Step 2 Press *-[5].
Step 3 Enter a “Master Arm/Disarm Code”.
Step 4 The ready light will flash.
Step 5 Enter the 2 digit “user number” (always enter 2 digit such as [0] – [3] for user 3, or [5] – [2] for user 52).
Step 6 Enter the new four (4) or six (6) digit “user code”.
NOTE: To delete a user code, enter *-*-*-* for a 4-digit code, or *-*-*-*-*-* for a 6-digit code.
Step 7 The ready light will flash indicating you are back at Step 4 above.
Step 8 If another “user code” needs to be deleted, return to Step 5.
Step 9 Press the [#] key while the ready light is flashing to exit the User Code Programming Mode